PCB PIEZOTRONICS 1303-111-03A датчик

027137-03022 PCB Piezotronics PCB L&T Hand Torque Wrench, w/LED & Auto-ID, 200 in-lb (22.7 Nm), 12-inch Handle, 3/8-inch Square Drive, 10-pin PT Receptacle
027375-07501 PCB Piezotronics PCB L&T Hand Torque Angle Wrench, w/Angle Encoder & Auto-ID, 500 ft-lb (678 Nm), 43-inch Handle, 3/4-inch Square Drive, 10-pin PT Receptacle
039001-01103 PCB Piezotronics PCB L&T Rotary Torque Only Transducer, w/Auto-ID, 10,000 Nm (7376 lbf-ft), 1 1/2-inch Square Drive, 10-pin PT Receptacle
039075-50301 PCB Piezotronics PCB L&T Rotary Torque Only Transducer, w/Auto-ID, 300 lbf-ft (406 Nm), 3/4-inch Square Drive, 10-pin PT Receptacle
054112-04103 PCB Piezotronics
054236-01804 PCB Piezotronics PCB L&T Fastener Force Washer, Metric, M36, 680 kN (153 klbf), 5-ft Integral Cable w/pigtails
080A12 PCB Piezotronics Adhesive mtg base, 0.75" hex x 0.2" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
080A47 PCB Piezotronics Petro wax, 175 gm (for accel adhesive mtg)
080C10 PCB Piezotronics Triaxial mtg adaptor, 0.87" cube, 10-32 thd each surface, anodized aluminum
081A21 PCB Piezotronics Isolation mounting stud, integral 10-32 to 10-32 male studs both ends, 0.75" hex
084A17 PCB Piezotronics Aluminum handle, 5-44 conn. (for Model 086E80)
084A28 PCB Piezotronics Vinyl impact cap, red (for Models 086)
084A51 PCB Piezotronics Adaptor (for Model 084A50 tip to Model 086C05)
102B PCB Piezotronics High frequency ICP® pressure sensor, 5000 psi, 1 mV/psi, 3/8-24 mtg thd, accel. comp., ground isolated
106B50 PCB Piezotronics ICP® microphone, 500 mV/psi, resolution 0.00007 psi (+86 dB), accel. comp.
111A21 PCB Piezotronics General purpose ICP® pressure probe, 100 psi, 50 mV/psi, 0.218" dia. diaphragm, accel. comp.
111A24 PCB Piezotronics General purpose ICP® pressure probe, 1000 psi, 5 mV/psi, 0.218" dia. diaphragm, accel. comp.
112A21 PCB Piezotronics High resolution ICP® pressure probe, 100 psi, 50 mV/psi, 0.218" dia. diaphragm, accel. comp.
113A34 PCB Piezotronics High frequency Invar ICP® pressure probe, 1000 psi, 5 mV/psi, 0.218" dia. diaphragm (low trans thermal sens.)
116B PCB Piezotronics High temperature (+650 F/343 C) pressure sensor, 100 psi, 6 pC/psi
1203-15A PCB Piezotronics PCB L&T load cell, low profile, 5000 lbf rated capacity, 50% overload protection, 2mV/V output 5/8-18 UNF-2B thread, PTO2E-10-6P connector.
1204-03A PCB Piezotronics PCB L&T Load cell, low profile, 50k lbf rated capacity, 50% static overload protection, 3mV/V output, 1 1/4 -12 UNF female thread, PT02E-10-6P connector, steel construction
1225-500L-CT PCB Piezotronics PCB L&T Load Button, 500 lbf capacity, 0.9-inch dia., 0.375 thick, integral 6 foot cable with bare leads
136A PCB Piezotronics Tourmaline hydraulic pressure calibration transfer standard, 20k psi, 0.2 pC/psi
138A06 PCB Piezotronics Tourmaline ICP® underwater blast sensor, 4.2" length, 5000 psi, 1 mV/psi
1403-03A PCB Piezotronics PCB L&T Fatigue load cell, low profile, 1k lbf rated capacity, 100% static overload protection, 1mV/V output, 5/8-18 UNF female thread, PT02E-10-6P connector, steel construction
1403-13A PCB Piezotronics PCB L&T fatigue rated load cell, low profile, 1000 lbf rated capacity, 300% overload protection, 1.0mV/V output 5/8-18 UNF-2B thread, PTO2E-10-6P connector.
201B01 PCB Piezotronics ICP® quartz force ring, 10 lb comp., 500 mV/lb
201B04 PCB Piezotronics ICP® quartz force ring, 1k lb comp., 5 mV/lb
208C03 PCB Piezotronics PCB L&T Platinum Stock Products, Multi-purpose, ICP® force sensor, 500 lb comp., 500 lb tension, 10 mV/lb
2305-01A PCB Piezotronics PCB L&T Reaction Torque Transducer, 300k in-lb/25k ft-lb (33.9 kN-m) rated capacity, 50% static overload protection, 14-in (355.6 mm) Steel Flange
3122-04A PCB Piezotronics PCB L&T Rotary Torque Transducer (Slip Ring), 88.5 in-lb/7.4 ft-lb(10 N-m) rated capacity, 100% static overload protection, 3/8-in (9.525 mm) Shaft
3124-02A PCB Piezotronics PCB L&T Rotary Torque Transducer (Slip Ring), 1,000 in-lb/83 ft-lb (113 N-m) rated capacity, 100% static overload protection, 1-in (25.4 mm) Shaft
3126-01A PCB Piezotronics Torque Shaft, Promess, 1Nm
3126-02A PCB Piezotronics Torque Shaft, Promess, 5Nm Capacity
320C11 PCB Piezotronics ESS mini (2 gm), quartz shear ICP® accel., 5 mV/g, 2 to 10k Hz, 5-44 side conn., 5-40 mtg stud, to +325 F/+163 C
320C15 PCB Piezotronics ESS mini (2 gm), quartz shear ICP® accel., 10 mV/g, 2 to 10k Hz, 5-44 side conn., 5-40 mtg stud, to +325 F/+163 C
333B35 PCB Piezotronics Modal array, ceramic shear ICP® accel, 100 mV/g, 0.5 to 3k Hz, 10-32 top conn., 5-40 stud mount
333B41 PCB Piezotronics Modal array, ceramic shear ICP® accel, 500 mV/g, 0.5 to 3k Hz, 10-32 electrical bottom conn.
339A30 PCB Piezotronics Triaxial ICP accelerometer, 10 mV/g, adhesive mount, with low temperature coefficient
339B03 PCB Piezotronics 20 mV/g quartz shear triaxial accel.
340A75 PCB Piezotronics High-temp., miniature (2 gm), ceramic shear charge accel., 3 pC/g, 12k Hz, M3 side conn., M3 stud mount
3501A202KG PCB Piezotronics Shock accelerometer, 2 kg, sensor installed in chip carrier (SMT).
350B21 PCB Piezotronics Shock, ceramic-shear, ICP® accel., 0.05 mV/g, 100k g range, case isolated, 10-ft integral cable
351B42 PCB Piezotronics Cryogenic, quartz shear ICP® accel., 100 mV/g, 1 to 2k Hz, 10-32 top conn. (-320 to +250 F/-196 to +121 C)
352A72 PCB Piezotronics Miniature, lightweight (0.6 gm), ceramic shear ICP® accel., 10 mV/g, built-in 15 kHz LP filter, titanium case, attached lightweight cable
352C34 PCB Piezotronics Platinum Stock Products, High sensitivity, ceramic shear ICP® accel., 100 mV/g, 0.5 Hz to 10k Hz, 10-32 top conn.
352C44 PCB Piezotronics Low profile, miniature (3 gm), ground isolated, ceramic shear ICP® accel., 100 mV/g, 1 Hz to 8k Hz
352C67 PCB Piezotronics High sensitivity, miniature (2 gm), ceramic shear ICP® accel., 100 mV/g, 0.5 to 10k Hz, 10-ft attached cable
353B17 PCB Piezotronics High frequency, quartz shear ICP® accel., 10 mV/g, 1 to 10k Hz, 10-ft integral cable
356A12 PCB Piezotronics Triaxial ICP® accelerometer, 100 mV/g, 50 g, 0.5 to 5k Hz, 5gm, 5 foot attached cable
356A16 PCB Piezotronics Platinum Stock Products, Triaxial, high sensitivity, ceramic shear ICP® accel., 100 mV/g, 0.5 to 5k Hz, aluminum hsg, 4-pin conn.
356A24 PCB Piezotronics Triaxial, low-profile, ceramic shear ICP® accel., 10 mV/g, 1 to 9k Hz, titanium hsg, mini 4-pin conn.
356A26 PCB Piezotronics Triaxial, general purpose, ceramic shear ICP® accel., 50 mV/g, 1 to 5k Hz, 4-pin conn.
356A66 PCB Piezotronics Triaxial, ceramic shear ICP® accel., 10 mV/g, 2 to 4 kHz, 14 mm cube size, w/built-in filter
356A70 PCB Piezotronics Triaxial, miniature (8 gm), charge output accel., 2.7 pC/g, 5k Hz, (3) 5-44 conn.
357B11 PCB Piezotronics High temp., miniature (2 gm), ceramic shear, charge output accel., 3 pC/g, 12k Hz, 5-44 side conn.(-95 F to +500 F)
3711B1210G PCB Piezotronics MEMS DC accelerometer, 200 mV/g, +/-10g range, 0 to 1000 Hz, integral cable
3713B1110G PCB Piezotronics Platinum Stock Products, Triaxial MEMS DC accelerometer, 200 mV/g, +/- 10 g, +6 to 30 VDC excitation
3713B1210G PCB Piezotronics Triaxial MEMS DC accelerometer, 200 mV/g, +/- 10g, +6 to 30 VDC excitation, integral cable
3741B1230G PCB Piezotronics Differential MEMS DC accelerometer, 67 mV/g, 30 g, 0 to 1000 Hz, through hole mtg., 10 ft integral cable
377A26 PCB Piezotronics Probe microphone, ICP®
393B31 PCB Piezotronics Seismic, high sensitivity, ceramic flexural ICP® accel., 10 V/g, 0.1 to 200 Hz, 2-pin top conn.
4115A-04A PCB Piezotronics PCB L&T Torque Sensor, Rotary Transformer, 500 in-lb Capacity FS, Flanges and Splines per AND10262 & AND20002
426E01 PCB Piezotronics ICP® microphone preamplifier 1/2" to be used with prepolarized condenser microphone.
481A03 PCB Piezotronics 16-channel, line-powered, ICP® sensor signal cond., fine gain, computer/front panel control, programmable filter
602D12 PCB Piezotronics
603C01 PCB Piezotronics Platinum Stock Products, General purpose, industrial, ceramic shear ICP® accel, 100 mV/g, 0.5 to 10k Hz, top exit, 2-pin conn., single point ISO 17025 accredited calibration
605B02 PCB Piezotronics Biaxial ring-style, industrial, ceramic shear ICP® accel, 500 mV/g, 0.5 to 5k Hz, side exit, 3-pin conn., biaxial single point ISO 17025 accredited calibration
623C10 PCB Piezotronics High-freq., industrial, ceramic shear ICP® accel, 10 mV/g, 0.8 to 15k Hz, top exit, 10-ft integral cable, frequency sweep ISO 17025 accredited calibration
624B01 PCB Piezotronics Ring-style, industrial, quartz shear ICP® accel, 100 mV/g, 0.8 to 10k Hz, side exit, 2-pin conn., frequency sweep ISO 17025 accredited calibration
625B00 PCB Piezotronics Ring-style, industrial, ceramic shear ICP® accel, 10 mV/g, 0.2 to 10.5k Hz, side exit, 2-pin conn., frequency sweep ISO 17025 accredited calibration
625B11 PCB Piezotronics Ring-style, industrial, ceramic shear ICP® accel, 100 mV/g, 0.2 to 10.5k Hz, side exit, 10-ft integral cable, frequency sweep ISO 17025 accredited calibration
626B11 PCB Piezotronics Low freq., industrial, ceramic shear ICP® accel, 100 mV/g, 0.2 to 10k Hz, top exit, 10-ft integral cable, frequency sweep ISO 17025 accredited calibration
640B10 PCB Piezotronics Industrial vibration sensor, 4 to 20 mA output, 0 to 0.5 in/sec pk, 3 to 1k Hz, top exit, 10-ft integral cable
66332ANZ1 PCB Piezotronics OST ACCELEROMETER TR1BCN
686B14 PCB Piezotronics USB Programmable vibration switch
686B61 PCB Piezotronics Smart Vibration Switch
686B62 PCB Piezotronics Smart Vibration Switch
ACS-4 PCB Piezotronics Single axis, low frequency phase and amplitude response cal from 0.5 to 10 Hz, (requires ACS-1 and minimum sensitivity of 20 mV/g)
EX611A00 PCB Piezotronics High temperature,intrinsically safe, charge mode accelerometer, 10 pC/g sensitivity, 1200 degree F, 10 ft integral hard-line cable.
EX646B71 PCB Piezotronics ACCELEROMETER
HT426E01 PCB Piezotronics Platinum Stock Products, High temperature 1/2-inch preamplifier
HT602D01 PCB Piezotronics Platinum Stock Products, High temperature 602D01
HT624B01 PCB Piezotronics Model 624B01 with high temperature range option (+325 F/+163 C)
HT641B61 PCB Piezotronics 4-20 MA TRANSMITTER
LASERTACH PCB Piezotronics ICP® LaserTach with BNC output
M080A12 PCB Piezotronics Metric adhesive base, 0.75" hex x 0.2" thk, M6 x 0.75 thd, aluminum w/insulating hardcoat finish
M080A68 PCB Piezotronics Metric adhesive base, 0.875" hex x 0.2" thk, M6 x 0.75 thd, aluminum w/insulating hardcoat finish
M081A27 PCB Piezotronics Metric mtg stud, 5-40 to M3 x 0.50 long
M1403-04B PCB Piezotronics Fatigue load cell, low profile, 12.5 kN rated capacity, 100% static overload protection, 1.5mV/V output, M16x2-4H female thread, PC04E-10-6P connector, steel construction
M1411-02A PCB Piezotronics Fatigue load cell, low profile, 450 kN rated capacity, 100% static overload protection, 1.5mV/V output, M72x2-4H female thread, PT02E-10-6P connector, steel construction
M1414-02A PCB Piezotronics
M1630-04C PCB Piezotronics S-Type Load Cell, 500 N rated capacity, 150% of RO static overload protection, 2mV/V output, M6 x 1.0 threads, integral 3m cable with open end, aluminum construction
T1403-02A PCB Piezotronics Fatigue load cell, low profile, 500 lbf rated capacity, 100% static overload protection, 1mV/V output, 5/8-18 UNF f-thread, PT02E-10-6P connector, steel, TEDS